ASTM F2164 EPUB

An American National StandardDesignation: F – 02 Standard Practice for Field Leak Testing of Polyethylene (PE) Pressure P. described in ASTM F, “Standard Practice for. Field Leak Testing of Polyethylene (PE) and. Crosslinked Polyethylene (PEX) Pressure Piping. Systems Using. As a similar alternate, ASTM F instructs to fill and then thermally stabilize the pipeline with no air entrapment, pressurize the pipeline at test pressure for.

Author: Kagabei Kazraktilar
Country: Seychelles
Language: English (Spanish)
Genre: Life
Published (Last): 1 November 2004
Pages: 287
PDF File Size: 19.23 Mb
ePub File Size: 10.20 Mb
ISBN: 217-8-96028-554-4
Downloads: 63902
Price: Free* [*Free Regsitration Required]
Uploader: Turamar

Contact the joint or connection manufacturer for information. Such systems astm f2164 contain lower pressure rated or non-pressure rated components that cannot be isolated from test pressure, or temporary caps or closures may not be practical.

For field-testing of plastic gravity flow sewer lines, see Test Method F To prevent Poisson-effect disjoining, take measures such as the installation of astm f2164 joint restraints diametrical clamps and tie-rods on in-line non-restrained joints, installing in-line thrust anchors at the ends of the fully restrained section, or isolating the fully restrained test section from piping with non-restrained or partially astm f2164 joints.

Historical Version s – view previous versions of standard. It is the responsibility of the user of this standard to establish appropriate safety and astm f2164 practices and determine the applicability of regulatory limitations prior to use. The amount of make-up astm f2164 expansion allowance will vary because expansion is not linear.

Work Item s – proposed revisions of this standard. Astm f2164 view current version of standard. Warning —Safety is of paramount importance when conducting hydrostatic pressure leak tests because testing under pressure may cause sudden t2164 rupture or failure.

ASTM F2164 – 13

For safety reasons, some manufacturers prohibit or astm f2164 pneumatic pressure testing of their products. Failure during a pressure leak test can be explosive, violent, and dangerous, especially if a compressed gas astm f2164 used.

Link to Active This link will always route to the current Active version of the standard. The ratio of decrease to elongation is the Poisson ratio. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered astm f2164. In a compressed gas test, both the pressure stress on the system and the energy used to compress the gas are released at a failure.

For safety reasons, some manufacturers prohibit or restrict pneumatic pressure testing of their products. Under test pressure, piping materials will expand slightly in diameter and contract in length slightly according to the Poisson ratio of the material. Astm f2164 does not verify if a piping material or a piping system design is suitable for pressure service.

Note 2 — When a tensile stress is applied to a material, it will astm f2164 in the direction of the applied stress, and will decrease in dimension at right angles to the direction of the applied stress. Additional safety information is presented in Section aztm and throughout this standard.

This procedure compensates for expansion with an initial expansion phase, followed by a test phase. astm f2164

Link to Active This link will astm f2164 route to the current Active version of astk standard. Contact component manufacturers for information about testing with gas under pressure. Referenced Documents astm f2164 separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. f214

ASTM International – Standard References for ASTM F – 13

In these systems, leak inspections should be conducted during and after installation. For field-testing of plastic gravity flow sewer lines, see Test Method F Astm f2164 suitability of a piping system for pressure service and its pressure rating or operating pressure is determined solely by its design and its installed components.

Poisson-effect length reduction may affect or cause disjoining in other contiguous sections astm f2164 have partially restrained or non-restrained joints, such as bell-and-spigot joints, when such joints are in-line with the test section.

See also Test Method F Astm f2164 component manufacturers for information about testing with gas under pressure. Additional safety information is presented in Section 7 and throughout this standard.

astm f2164 In a compressed gas test, both the pressure stress on the system and the energy used to compress the gas are released at a failure. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as f21664 astm f2164 the standard.