2SC Transistor Datasheet pdf, 2SC Equivalent. Parameters and Characteristics. C ; Transistor BJT NPN 50V mA mW MHz, TO voltage VCE (sat) • Complementary pair with 2SA and 2SA 28 Jan Part Number: C Function: ST 2SC / C NPN Silicon Epitaxial Planar Transistor Maker: Unspecified Pinouts: C datasheet.

Author: Ferg Gom
Country: Czech Republic
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 6 May 2013
Pages: 145
PDF File Size: 9.78 Mb
ePub File Size: 5.66 Mb
ISBN: 351-9-71871-522-1
Downloads: 11461
Price: Free* [*Free Regsitration Required]
Uploader: Mujin

I could do it with c1740 transistor quad NOR gate, but that is a 14 pin DIP package that needs 12 wires connected when you include tying unused inputs to ground. Sign up or log in Sign up c1740 transistor Google. I built an inverter based on this thread: I’ve been working with an Arduino lately, and building various breadboard circuits.

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. Post as a guest Name. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand c1740 transistor your continued use of the website is subject to these policies.

So is that a rule of thumb, make r2 10x the r1 value? Thank you very much. Sign up c1740 transistor Facebook.

What is it about switching transistors that makes them unsuitable for a circuit like this? Is the flat side facing up in the red box above? Golden rule c1740 transistor always read the data sheet and if you can’t find one then don’t assume. Questions Tags Users Badges C1740 transistor.

Saturated means fully on; and 10 c1740 transistor or less 20 is usually OK and saves base current. It’s maddening that the pinouts aren’t the same. I understand that a “real” CMOS inverter is a better choice for this application, but bear with c1740 transistor. I could not find datasheet for the C Why can’t the industry standardize on one pinout convention for transistr given type of component and package?

If so, note the pins red line – they are not the standard pin-out with base in the centre like the 2NA: I just swapped the base and collector in c1740 transistor breadboard, and now the C works in place of the A. This site uses cookies to deliver our services and to show you relevant ads and job listings.

I’m having a transisstor trouble understanding the pinout diagram from c1740 transistor data sheet. Might be a silly question but did you check the pinout of the switching device?

20PCS 2SC1740 C1740 Transistor TO-220

The base and collector are reversed from the 2nA? Sign up using Email and Password. So transidtor leftmost pin is the emitter, the middle is the collector, and the rightmost pin is the base? DuncanC I would say that in the diagram where C1740 transistor drew the c1740 transistor box the flat side is facing the reader.

Why won’t a switching transistor c1740 transistor in this circuit. Hey try it both ways or even test it with a multimeter for diode between base and collector and base and emitter. Also, I would use c1740 transistor much lower resistor instead of k, maybe 10k.

Maybe it’s a 2SC That takes a lot of room on my breadboard and a lot of time to set up.

npn – Why won’t a switching transistor work in this circuit – Electrical Engineering Stack Exchange

A simple example was to build a c1740 transistor based inverter for a project involving baud c1740 transistor combination at 5v. How to invert a digital signal The circuit looks like this: Andy aka k 9 Duncan C 1 9 I don’t know c1740 transistor sure what these are. Exactly 10x, or 10 or less? Are you sure that a it is an NPN transistior b with a sufficient B current amplification factor and c that you connected it correctly?

NPN C Datasheet –

How to invert a digital signal. I thought switching transistors were tuned for very “snappy” response that tends to c1740 transistor either fully on or fully off.

If the pins are not in c1740 transistor order that would certainly explain it though!

These are loose parts that I’ve collected in various electronics kits and projects through the years.